Table of Contents

Design and Fabrication Of Tension less Bike Full Report Download

Abstract:

An automobile is a wheeled motor vehicle used for transporting passengers, which also carries its own engine or motor. But normally two wheeler are used most of the people which is economical. Motorcycles are one of the most affordable forms of motorized transport in many parts of the world and, for most of the world’s population; they are also the most common type of motor vehicle. There are around 200 million motorcycles (including mopeds, motor scooters and other powered two and three-wheeler) in use worldwide, or about 33 motorcycles per 1000 people.While people choose to ride motorcycles for various reasons, those reasons are increasingly practical, with riders opting for a powered two-wheeler as a cost-efficient alternative to infrequent and expensive public transport systems, or as a means of avoiding or reducing the effects of urban congestion. In places where it is permitted, lane splitting, also known as filtering, allows motorcycles to use the space between vehicles to move through stationary or slow traffic.In this motorcycle, major accidents occur due to the carelessness. Some of them forgot to take the side stand and they start driving with that side stand. This leads to an accident. Sometimes if we are going to a long drive there is a chance of air leakage in our bikes or our bike may get puncher. In that time there is no puncher shop nearby us. So we get into trouble.

INTRODUCTION

While people choose to ride motorcycles for various reasons, those reasons are increasingly practical, with riders opting for a powered two-wheeler as a cost-efficient alternative to infrequent and expensive public transport systems, or as a means of avoiding or reducing the effects of urban congestion. In places where it is permitted, lane splitting, also known as filtering, allows motorcycles to use the space between vehicles to move through stationary or slow traffic.

In this motorcycle, major accidents occur due to the carelessness. Some of them forgot to take the side stand and they start driving drive there is a chance of air leakage in our bikes. In that time there is no puncher shop with that side stand. This leads to an accident. Sometimes if we are going to a long nearby us. So we get into trouble.

Many engineers found out solutions for reduce the tension of bike. But it will not so much effective than our discovery.

Our aim is to reduce the tension of one who is driving the vehicle. Because some of the carelessness leads to a death. So every time we always aware of that. So our mini project helps a little bit to reduce those kind of incidents. Our objective is to inflate the tyre in some emergency conditions where there is no helping hands.This method is one of the easiest methods and also the cheapest methods

Our mini project consists of two things:

1. Side Stand Indicator Modulation

2. A Compressor Of Less Weight

These two things are most important for all the bikes. All the bike riders knew how important these two things are. We are doing some of the alterations in the bike to make a successful of these two.

COMPRESSOR IN BIKE:

Puncher in is commonly occurring thing bike. Nowadays most of Motorbike Company introduces the tubeless tyres. It decreases the air slowly if the wheel gets punched has been occurred. Anyway this will also need air to move some distance.

Design and Fabrication Of Tension less Bike - TYRE INFLATION — Design and Fabrication Of Tension less Bike – TYRE INFLATION

In the same way in the normal tube present in the tyres also . But in this normal tube using tyres the air will leaking out very rapidly than compare to tubeless tyres .

HOW TO INFLATE:

In this we made small modifications in our bike engine and additionally a TVS 50 engine is attached with that. Then we used this engine as a compressor by removing all fins of the engine and some modifications.

First of all let see that what is an engine and details about two stroke engine….

OUR MODIFICATION IN THIS ENGINE:

We cut the fins of the engine by using different mechanical methods. Because we are using this engine as a compressor only. So there is no chance of producing heat. For that it will be ignored. And also to reduce the weight of the engine we also cut the other unwanted things. There are many methods to remove the fins; we use a milling machine to remove the fins which is simple than other mechanical methods.

See Project on Tyre Inflation:

1) TYRE INFLATION & DEFLATION SYSTEM FOR FOUR WHEELER

2) Design and Fabrication of Automatic Tyre Inflation System

3) Seminar On Self inflating tyres -PPT and Report Download

SIDE STAND:

The side stand is the one of the most nice founded thing of our senior engineer and attached to bike instead of the centre stand most of the times people use only side stand in their bike because it easy to use compare to centre stand.

OUR SOLUTION REGARDING THIS PROBLEM:

Our solution is based on the principle of the key and lock present in bike i.e. when the side stand is been used the bike cannot be started until the side stand is taken. Then if we take the side stand and use the starter to start the bike then it will start this is the new method of us found apart the existing one.

OUR MECHANISM IN THIS SOLUTION:
We have added a additional circuit to the existing circuit. We have taken a wire or looped a wire from the ignition system and connect it to a plate. In the mean while the other wire is looped from earth or from ground and it is connected to the other plate. Now these wire are been kept in the side stand switch.

ADVANTAGES:

• For the side stand we provide a manual setup.

• If the battery becomes the chargeless battery sensors will not produce the beep sound properly, but our set up will not like this.

• If we are in helpless to inflate the tyre our setup will helps a lot.

• It can also be done by a person having basic knowledge of automobiles.

• Cost is less.

• Less maintenance required.

CONCLUSION:

The primary goal of this mini project is to find out some useful things which makes us feel less tension while we driving a two wheeler. Thus we find out the things which makes useful for many people. In this busy world we have a lots of work to do. In this busy schedule, it will happened to forgot small things. So we hope that our project helps a little bit to the people. Our future aim is to fit these compressor inside the engine guard. Some of the bikes like Yamaha, fazer and most of the sports bike have this engine guard. If we will fit this compressor in this engine means it will helps a lot.