Disc Brake | Construction , Working Principle , types and Rotor Materials

Disc Brake | Construction , Working Principle , types and Rotor Materials

Brake rotors of disc brakes rotate with the wheels, and brake pads, which are fitted to the brake calipers, clamp on these rotors to stop or decelerate the wheels. The brake pads pushing against the rotors generate friction, which transforms kinetic energy into a thermal energy.

This thermal energy generates heat, but since the main components are exposed to the atmosphere, this heat can be diffused efficiently. This heat-dissipating property reduces brake fade, which is the phenomenon where braking performance is influenced by the heat. Another advantage of disc brake is its resistance to water fade, which occurs when the water on the brakes significantly reduces braking force. When the vehicle is in motion, the rotor spins at high speeds and this rotational motion discharges the water from the rotors themselves, resulting in stable braking force.

Read also : Seminar On Ceramics Disc Brakes- Report Download

CONSTRUCTION OF DISC BRAKES 

The brake rotor (disc) which rotates with the wheel, is clamped by brake pads (friction material) fitted to the caliper from both sides with pressure from the piston(s) (pressure mechanism) and decelerates the disc rotation, thereby slowing down and stopping the vehicle.

Disc Brake Components
Disc Brake Components

1. Rotor:

Circular disc bolted to the wheel hub that spins with the wheel. Rotors are most commonly made of cast iron or steel; however, some very high-end cars use a carbon ceramic rotor. Rotors can be slotted or drilled for better heat dissipation.

2. Brake pads:

Component that pushes into the rotor, creating the friction that slows and stops a car. They feature a metal portion called a shoe and a lining that is attached to the shoe. The lining is what actually comes in contact with the rotor and wears away with use. Linings are made of different materials and fall into three categories: organic, semi-metallic and ceramic. The lining material chosen will impact the length of brake life, the amount of noise heard when the brakes are applied, and how quickly the brakes bring a car to a halt.

3. Piston:

Cylinder connected to the brake system hydraulics. The piston is what moves the brake pads into the rotor when the driver presses the brake pedal. Some brake systems have a single piston that moves both pads, while others have two pistons that push the brake pads from each side of the rotor. Others still have four, six, or even eight pistons for higher braking power, at the expense of added cost and complexity.

4. Caliper:

Housing that fits over the rotor and holds the brake pads and pistons, as well as contains ducting for brake fluid. There are two types of brake calipers: floating (or sliding) and fixed. Floating calipers “float” over the rotor, and only have pistons on a single side. When the driver presses the brakes, the pistons press the brake pads on one side into the rotor, which causes the caliper to slide over so that the pads on the non-piston side of the caliper also contact the rotor. Fixed calipers are bolted in place, and instead have pistons on both sides of the rotor that move when the driver applies the brakes. Fixed calipers apply brake pressure more evenly and clamp more firmly on the rotor, however floating calipers are found on most cars and are perfectly adequate for everyday driving.

5. Sensors:

Some vehicles have brakes that contain sensors embedded in the brake pads which work to tell the driver when the pads are worn out. Other brake sensors play a part in the vehicle’s ABS system.
Disc brakes are generally used in passenger cars, but due to their stable performance at higher speeds and resistance to brake fade, they are gradually spreading into the commercial vehicle segment, where drum brakes were traditionally chosen for their longer service life. There are two types of disc brakes.
The “opposed piston type disc brake” has pistons on both sides of the disc rotor, while the “floating type disc brake” has a piston on only one side. Floating caliper type disc brakes are also called sliding pin type disc brakes.

WORKING PRINCIPLE

When the driver steps on the brake pedal, the power is amplified by the brake booster (servo system) and changed into a hydraulic pressure (oil-pressure) by the master cylinder. The pressure reaches the brakes on the wheels via tubing filled with brake oil (brake fluid). The delivered pressure pushes the pistons on the brakes of the four wheels. The pistons in turn press the brake pads, which are friction material, against the brake rotors which rotate with the wheels. The pads clamp on the rotors from both sides and decelerate the wheels, thereby slowing down and stopping the vehicle.

disc brake system
disc brake system

• When brake pedal is pressed, the high-pressure fluid from the master cylinder pushes the piston outward.
• The piston pushes the brake pad against the rotating disc.
• As the inner brake pad touches rotor, the fluid pressure exerts further force and the caliper moves inward and pulls the outward brake pad towards the rotating disc and it touches the disc.
• Now both the brake pads are pushing the rotating disc, a large amount of friction is generated in between the pads and rotating disc and slows down the vehicle and finally let it stop.
• When brake pad is released, the piston moves inward, the brake pad away from the rotating disc. And the vehicle again starts to move.

TYPES OF DISC BRAKES

There are two types of disc brakes. One is called the “opposed piston type disc brake” which has pistons on both sides of the disc rotor, and the other is the “floating type disc brake” which has a piston on only one side. The floating type disc brakes are also called the sliding pin type disc brakes.

1. Opposed Piston Type Disc Brakes

  • The opposed piston type is a disc brake which has pistons on both sides of the disc rotors.
  • The opposed piston type disc brake features stable braking force as well as a high level of controllability.
  • The swept areas of the brake pads are enlarged to increase braking force, and here opposed piston types are favored.
  • This is because of its advantage where the number of pistons can be increased to realize even distribution of pressure on the rotors from both sides. Depending on size of the brake pads, there are several types, including the 4-pot type which has two pistons on each side for a total of four, and the 6-pot type which has three pistons on each side for a total of six.

2. Floating Type Disc Brakes

  • Floating type is a disc brake which has a piston on only one side, and is also called the sliding type disc brake.
    On the floating type disc brakes, the piston pushes the inner brake pad against the rotor when the brakes are engaged. This generates a reaction force that moves the caliper itself along the slide pin, pushing the outer pad against the rotor to clamp it from both sides.
  • Many passenger car disc brakes are of the floating caliper type, since this type has a relatively simple and lightweight construction, which allows for lower manufacturing costs.
  • Floating type disc brakes for commercial vehicles
  • Disc brakes are used mainly for passenger cars, but due to their consistent performance at higher speeds and resistance to brake fade, they are gradually spreading into the commercial vehicle segment, where drum brakes were traditionally chosen for their resistance against wear.

TYPES OF ROTOR

1. Smooth Rotors

Smooth rotors are identified by their flat, smooth surface. For most cars and trucks on the road, smooth rotors are original equipment (OE) because of their versatility for many driving conditions. The main benefit of smooth rotors is that they tend to wear evenly, helping your brake pads last longer. If you want to keep the smooth rotor but still go for the upgrade, look for premium metal that absorbs more heat.

2. Drilled or Dimpled Rotors

Drilled rotors are identified by the pattern of holes that have been drilled all the way through the rotor disc. Dimpled rotors are similar, though instead of holes there are dimples that have been drilled to the rotor’s minimum thickness level, retaining more structural integrity than a fully drilled rotor. These rotor types help the brake pads to better grip the rotor, giving it more initial bite and increasing stopping power.

*Note that drilled or dimpled rotors are typically found in combination with slotted rotors.

3. Slotted Rotors

Slotted rotors are recognized by carved lines found on the rotor. These carved slots help to cool the rotor during high performance use. They also help to remove dirt and other debris from the disc and brake pad, helping to maintain consistent contact for more efficient braking. Slotted rotors are perfect for vehicles that see frequent, heavy towing.

4. Drilled/Dimpled and Slotted Rotors

Rotors that are both drilled (or dimpled) and slotted, while effective, are best for trucks that want the added aesthetic, such as those with wheels that have a more open design. Not only will they look great through an open wheel, but the drilled holes assist with initial bite while the slots are designed to remove dust and debris from between the rotor and brake pad.

Read more : Types of Brakes | Different types of Braking System

ROTOR MATERIALS

Brake rotors can be made of six different materials, each with its own advantages. Let’s take a look at each.

1. Cast Iron

This is the very definition of old school when it comes to a brake rotor. It’s one or two pieces and gets the job done. In fact, it’s the most common material for brake rotors. The right design (usually two-piece) can even work well in a performance vehicle. However, it’s also the heaviest option, which affects the overall weight of your car and its handling, since that weight is right up there with your front wheels.

2. Steel

Steel has been the racer’s choice for years, because a steel brake rotor is thinner, weighs less and handles heat better. The downside: Steel rotors aren’t as durable as some others, and warped rotors can cause noise and a pulsating pedal when you brake.

3. Layered Steel

Layering sheets of steel together and laminating them makes them resistant to the warping you might find in a straight steel brake rotor. It’s a favorite of racers who don’t want frequent brake rotor replacement and repair, but manufacturers are currently only targeting professional racers and production is limited, so it’s not terribly common in passenger vehicle applications.

4. Aluminum

Aluminum brake rotors dissipate heat quickly, but they also melt at a lower temperature than other options. Aluminum is a favorite for motorcycles, which weigh less and are easier on the rotors when braking than a heavy car, truck or SUV.

5. High Carbon

These are iron, but with a lot of carbon mixed in. They can take a lot of heat and dissipate it quickly. The metallic content helps the rotor avoid cracking under high stress, and brake noise and vibration are reduced as well. The only downside is price, which is significantly higher than straight iron or aluminum.

6. Ceramic

What’s your favorite supercar? Ferrari? Porsche? Lamborghini? Odds are it’s packing ceramic brake rotors. They offer the highest heat capacity (85 percent higher than cast iron) and superior dissipation, and they maintain a more consistent force and pressure as the temperature of the rotors rises. Ceramic is the highest-performance brake rotor available today.

ADVANTAGES AND DISADVANTAGES

Advantages of Disc Brakes

1. It is lighter than drum brakes.
2. It has better cooling ( because the braking surface is directly exposed to the air)
3. It offers better resistance to fade.
4. It provides uniform pressure distribution
5. Replacement of brake pads are easy.
6. By design they are self-adjusting brakes.

Disadvantages of Disc Brakes

1. It is costlier than drum brakes.
2. Higher pedal pressure is required for stopping the vehicle. This brake system is installed with vacuum booster.
3. No servo action is present.
4. It is difficult to attach a suitable parking attachment.


More Resources : 

Automobile Engineering Parts and System Notes , Article

Automobile Trends , News articles , Notes

Mechanical Subjectwise Basic Concept Notes ,Articles


 

Sachin Thorat

Sachin is a B-TECH graduate in Mechanical Engineering from a reputed Engineering college. Currently, he is working in the sheet metal industry as a designer. Additionally, he has interested in Product Design, Animation, and Project design. He also likes to write articles related to the mechanical engineering field and tries to motivate other mechanical engineering students by his innovative project ideas, design, models and videos.

Leave a Reply

Your email address will not be published. Required fields are marked *

This site uses Akismet to reduce spam. Learn how your comment data is processed.

Recent Posts