Basic Of Measurement | Metrology Interview Question and Answers

Basic Of Measurement | Metrology Interview Question and Answers

Basic Of Measurement | Metrology Interview , Viva, Oral Question and Answers

1. What is Range of measurement?

The physical variables that are measured between two values. One is the higher calibration value H, and the other is Lower value L, The difference between H, and L, is called range.

2. What is Resolution?

The minimum value of the input signal is required to cause an appreciable change in the output known as resolution.

3. Differentiate between sensitivity and range with suitable example.

Example: An Instrument has a scale reading of 0.01 mm to 100 mm. Here, the sensitivity of the instrument is 0.01 mm i.e. the minimum value in the scale by which the instrument can read. The range is 0.01 to 100 mm i.e. the minimum to maximum value by which the
instrument can read.

4. Define system error and correction.

Error: The deviation between the results of measured value to the actual value.

Correction: The numerical value which should be added to the measured value to get the correct result.

5. Define: Measurement.

Measuring is the physical quantity or property like length, diameter, and angle to be measured.

metrology types
metrology types

6. Define: Deterministic Metrology.

The metrology in which part measurement is replaced by process measurement. The new techniques such as 3D error compensation by CNC systems are applied.

7. Define over damped and under damped system.

Over damped – The final indication of measurement ii approached exponentially from one side.
Under damped – The pointer approach the position corresponding to final reading and makes a number of oscillations around it.

8. Give any four methods of measurement

1. Direct method.
2. Indirect method.
3. Comparison method.
4. Coincidence method.

9. Give classification of measuring instruments.

1. Angle measuring Instruments.
2. Length measuring Instruments.
3. Instruments for surface finish.
4. Instruments for deviations.

10. Define True size.

True size is Theoretical size of a dimension.

11. Define Actual size.

Actual size = Size obtained through measurement with permissible error.

12. What is Hysteresis?

All the energy put into the stressed component when loaded is not recovered upon unloading. So, the output of measurement partially depends on input called hysteresis.

13. Differentiate accuracy and Uncertainty with example.

  • Accuracy – Closeness to the true value.
  • Example: Measuring accuracy is ± 0.02mm for diameter 25mm.
  • Here the measurement true values lie between 24.98 to25.02 mm
  • Uncertainty about the true value = ± 0.02mm

14. Define Span.

The algebraic difference between higher calibration values to lower calibration value.
Example: In a measurement of temperature higher value is 200*C and lower value is 15000 C
means span = 200 – 150 = 500 C.

15. Differentiate between precision and accuracy.

Accuracy – The maximum amount by which the result differ from true value.
Precision – Degree of repetitiveness. If an instrument is not precise it will give different results for the same dimension for the repeated readings.

16. What is Scale interval?

It is the difference between two successive scale marks in units.

17. What is Response Time?

The time at which the instrument begins its response for a change measured quantity.

18. Define Repeatability.

The ability of the measuring instrument to repeat the same results g the act measurements for the same quantity is known as repeatability.

19. Explain the term magnification.

It means the magnitude of output signal of measuring instrument time’s increases to make it more readable.

20. Classify the Absolute error.

The absolute error is classified into
1. True absolute error.
2. Apparent absolute error.

21. What is Relative error?

Relative error is defined as the results of the absolute error and the, value of comparison used for calculation of that absolute error. The comparison may be true value or conventional true value or arithmetic mean for series of measurement.

22. Classify the errors.

The errors can be classified into
1. Static errors – Reading errors
– Characteristic errors,
– Environmental errors
2. Loading errors
3. Dynamic error.

23. What is the basic Principle of measurement?

It is the physical phenomenon utilized in the measurement. If energy kind of quantity measured, there must be a unit to measure it. So this will give the quantity to be measured in number of that unit.

24. What is Application of Legal Metrology ?

1. Industrial Measurements.
2. Commercial transactions.
3. Public health and human safety ensuring.

24. What is the need of inspection?

To determine the fitness of new made materials, products or component part and to compare the materials, products to the established standard.

25. What are the important elements of measurements?

The important elements of a measurement is
1. Measurand.
2. Reference.
3. Comparator.

More Resources /articles
Measurement Science and Metrology Notes , Articles
Latest seminar topic index - Report ,PPT Download
RAC / HVAC - Articles , Notes , Que and Answers
Mechanical Subjectwise Basic Concept Notes ,Articles


Sachin Thorat

Sachin is a B-TECH graduate in Mechanical Engineering from a reputed Engineering college. Currently, he is working in the sheet metal industry as a designer. Additionally, he has interested in Product Design, Animation, and Project design. He also likes to write articles related to the mechanical engineering field and tries to motivate other mechanical engineering students by his innovative project ideas, design, models and videos.

Leave a Reply

Your email address will not be published. Required fields are marked *

This site uses Akismet to reduce spam. Learn how your comment data is processed.

Recent Posts